NUMBER OF DISCS 18 (2 X 9) MINIMUM PTO POWER REQUIRED (HP (KW)) 235 (175) | |
UP TO 50 ACRES PER HOURThe importance of effective and efficient conditioning is clear. MegaCutter™ mounted disc mowers and disc mower-conditioners match capacity to your imagination. | |
THE COMBINATION THAT’S RIGHT FOR YOUNew Holland offers triple-swath productivity both with conditioning and without to fit your crops, your tractor horsepower and your budget. | |
DURABILITY TO HANDLE TOUGH CONDITIONSEvery part of the MegaCutter™ system is ruggedly built for high-speed mowing. Keeping knives sharp is easy with the standard quick-change knife system. | |
ROLL OR FLAIL CONDITIONINGIf your crops require conditioning, MegaCutter™ disc mower-conditioners offer you the choice of gentle rubber chevron intermeshing rolls perfect for legume crops or steel V-tine flail conditioning for grass hay. |
STEEL FLAIL TINE CONDITIONINGSteel flail tines are positioned at an angle to the rotor’s center, providing increased outward crop pressure against the adjustable conditioning hood and improving swath and windrow formation. You can adjust the hood to change the conditioning intensity. The semi-swinging flail tines allow obstructions to pass, for better protection compared to fixed poly or steel tines. And unlike conventional, free-swinging tines, they cannot swing back over center, but are held in the ideal place by centrifugal force for efficient and effective conditioning and uniform swath and windrow formation. | |
RUBBER CHEVRON INTERMESHING ROLLSRubber chevron intermeshing rolls provide full-stem crimping and cracking with a scrubbing action while handling the leaves of high-value feeds delicately, making it the ultimate solution for alfalfa and clover. You get gentle handling while making fast-drying swaths. | |
HIGHER RETAINED QUALITY THROUGH FAST DRYDOWNFaster hay drying not only means beating the weather, it allows you to get crop out of the field with maximum feed quality. New Holland offers three effective solutions for fast drying of high-quality feed, including gentle rubber chevron intermeshing rolls for alfalfa and other legume crops, flail tine conditioning for grass hay, and a lower-horsepower model with no conditioning that’s ideal for silage making. |
Mounting |
Rear-three point linkage |
Attachment |
Standard ASABE link ends Cat III / Cat IV |
Cutting width narrow setting (ft. in. (m)) |
30' 8" (9.32) |
Cutting width wide setting (ft. in. (m)) |
33' 6" (10.2) |
Cutting width adjustment |
Hydraulic adjustment 6 in. (152 mm) to 11 in. (279 mm) overlap |
Cutting height control |
Tractor rear top link adjustment |
Type |
Low profile spur gear |
Number of discs |
18 (2 x 9) |
Knives per disc |
2 |
Quick change knife system |
Standard |
Disc speed @ 1000 rpm PTO speed (rpm) |
3,000 |
Cutter bar protection system |
Shear hub system - Standard |
Flotation |
Up & back, hydropneumatic, adjustment on-the-go from monitor |
Cutting height (in. (mm)) |
2-4 (50-100) |
Type |
Chevron intermeshing rubber |
Drive method |
Enclosed gearbox |
Speed (rpm) |
900 |
Conditioner roll tension adjustment |
Tension spring |
Conditioner adjustment |
Adjustable tension / gap stop |
Type |
Tangential mounted steel v-tines |
Drive method |
Belt driven |
Speed (rpm) |
700 |
Conditioner gap adjustment |
Adjustable hood |
Minimum PTO power required (hp (kW)) |
235 (175) |
Hydraulic circuits required |
CCLS 1 LS - Power Beyond, 6.5-13.25 gpm (24.6-50.2 Lpm) 2175-2900 psi (150-200 bar) |
Electrical |
7-pin electrical connector for transport lights |
User interface / machine control |
Virtual Terminal Monitor with ISOBUS 11783 connector |
Hydraulic folding cutter bar end guards |
Standard |
Width-transport (ft. in. (m)) |
9' 4" (2.84) |
Height-transport (ft. in. (m)) |
13' 6" (4.12) |
Height-vertically parked storage position (ft. in. (m)) |
13' 1" (3.9) |
Operating weight (lbs. (kg)) |
6756 (3064) - Flail tine version, 7030 (3188) - Roll version |